Product size :2175*990*420~800 (mm)。
1,The bed frame is made of ≥30×60×1.5mm cold-rolled rectangular steel pipe, the thickness of the bed panel is ≥1.2mm, and the metal surface is treated by degreasing, phosphating, oil removal, corrosion prevention, rust prevention, etc., and high-quality epoxy resin powder is sprayed by electrostatic spraying and cured at high temperature. The film thickness is 60-80um, the adhesion reaches the level 0 standard, the spray solidification degree reaches 50kg knocking force, the finished surface coating film has no defects such as peeling, sticking paint and wrinkles, and has good corrosion resistance and impact resistance.
2. The bed panel is made of high quality cold rolled plate, the bed surface is three fold four groups, the specification is 800*900mm; 210*900mm; 390*900mm; 590*900mm; Anti-resonance 10-piece combination; Advanced production process design is adopted, both sides of each steel plate are used coil diameter Φ20mm round pipe to strengthen the process and increase the bending compressive strength of the bed surface; Each bed plate has 70*30mm R-angle concave and convex punching 6, the air vent area reaches more than 20% of the bed surface area, no acute Angle burr, high permeability, pressure resistance without deformation, no fluctuation, no resonance sound. The support arm of bed transmission adopts integrated forming stamping reinforcement to increase the compressive strength of the bed. Bed plate must be equipped with ABS engineering plastic side sleeve, specifications: 770*30mm=2; 170*30mm=2 pieces; 360*30mm=2; 540*30mm=2; The bed plate is equipped with Angle indicator, the end of the bed plate and the two sides of the bed plate must be equipped with two ABS material anti-slip devices, the overall size: length 60× height 90cm; Prevent the mattress from sliding around when the bed board rises and falls;
3.
3、Split lifting guardrail in line with IEC60601-2-52 safety standards of the new split lifting guardrail, the front and back fence gap is reduced, no need to be equipped with guardrail baffle, can be with the function of the bed at the same time, to maximize the protection of patient safety. When the guardrail is stressed inside and cannot be opened, it must be pressed from outside to inside to open the guardrail.
4、Operation panel: both sides of the guardrail are equipped with special operation panels to facilitate the operation of medical personnel, and the remote control lock button is equipped on the panel to prevent patients from misoperation. Add the safety position display light, when the bed body is set in the lowest position, the green light is displayed, which is convenient for medical staff to check the patient's safety position at night.
6、Ball Angle display The bed body has a ball Angle display for easy confirmation by medical staff.
7、Manual CPR function The bed body is equipped with manual CPR function on both sides, in case of emergency or power failure, the bed can be quickly restored to the level state in the raised state.
8、Hand-held remote control: equipped with hand-held remote control, easy operation.
9、Ergonomic guardrail: The upper part of the ergonomic guardrail is easy to hold and can be used as a help bar when the patient stands up.
10, binding device: under the bed plate, with binding device, left and right five.
11, drainage bag hooks: on both sides of the bed, a total of four drainage bag hooks.
12、Back bed plate C-type rise: When the back rises, the backplane shows a C-type rise path, which can effectively reduce the possibility of long-term bed patients suffering from bedsores and prevent the position from moving down.
13, central control lock system: diameter 125mm medical double-sided caster with locking, free, directional three-stage central control locking device, anti-corrosion, good acid resistance.
14、Weighing system:
Maximum weight: 200kg/440lb2, minimum weight: 0.1kg/0.2lb
Weighing error: ±0.25%F.S
Alarm accuracy: ±0.1kg
Display: LCD (liquid crystal display) +LED(backlight assistant version)
Weighing unit: kg/lb
1), continuous monitoring of weight: can continuously observe the weight change of the person, and alarm at the set point.
2), weight storage: When the weight is stable, it can lock and store at least 20 groups of data, and has power failure protection function.
3) Alarm range setting: 5%-95%F.S
4), alarm selection: weight change alarm. (Patient alarm at bed position: 1. Patient sitting up 2. Side seat 3. Out of bed)
15, the bed adopts imported motor, quiet and noiseless, equipped with a battery;
16, seven functions; Backplane folding Angle 0° ~ ≥75°, leg plate folding Angle 0° ~ ≥45°, overall lifting Angle 420~800mm, bed overall tilt Angle 0° ~ ≥17°, one-button heart chair, CPR one-button cardiopulmonary resuscitation function, back-leg linkage.
2. Product list:
1, bed body (bed surface, bed frame, central control caster, infusion rod jack, drainage hook, anti-collision wheel) 2, four-piece guardrail 3, guardrail controller 4, nurse controller 5, hand controller 6, LINK motor 7, headboard and tail board 8, backboard can be X-ray 9, five inch LCD display (patient information, out of bed alarm, weight record), configuration weighing system 10, stainless steel infusion rack